Standard Waveform

Sine, triangle, square, pulse, ramp up, ramp down, sinc (sin(x)/x), Gaussian pulse, noise

Maximum Frequency 

(FS=160 MHZ)

Waveform

DDS Mode

AWG Mode

Sine

30 MHz

6.25 MHz

Triangle

1 MHz

6.25 MHz

Ramp

1 MHz

6.25 MHz

Pulse

6.25 MHz

Square

30 MHz

50 MHz

Noise

1 MHz

Arbitrary Generator Mode

Sample Rate

10 mS/s to 100 MS/s

Sample Rate Resolution & Accuracy

4 digits or .01 Hz, whichever is lower

.01% accuracy

Vertical Resolution

12 bits

Waveform Memory

2 M samples

DDS Mode

Frequency Range, Resolution, and Accuracy

10 uHz to 30 MHz

10 uHz, resolution

50 ppm accuracy (OCXO option available for higher accuracy)

Non-Harmonic Spurious Components

< 60 dBc (DC to 1 MHz)

Distortion (2nd Harmonic Relative To Carrier)

 -60 dBc at < 200 KHz

< -35 dBc at < 2.0 MHz

< -20 dBc at < 20 MHz

Modulation

AM: Int./Ext. 0 -100%, DC to 20 KHz

FM: Int./ Ext.

FM Deviation: 0-100% (2 x Fc)

FM Modulation: DC to 20 KHz

Programmable Phase Offset

Range: 0-360 degrees

Resolution: 0.1 degrees

Main Output

Connector

Front panel BNC

Output Mode

On / Off

Output Impedance

50 Ω, +-/1%

Protection

Protected against shorts to ground and over-voltage

Amplitude Range

100 mV to 8Vpk-pk into 50 Ω; double into an open circuit.

0.01, 0.03, 0.1, 0.3, 1, 3, and 8-volt p-p FS ranges

Amplitude Resolution

3 digits

Amplitude Accuracy

+/- (2% of  programmed value + 5 mV) <1V

+/-(1% of  programmed value + 10 mV)  =>1V

Offset Range

0 to ± 4 V, amplitude dependent

Offset Resolution

3 digits

Offset Accuracy

±(1% of  programmed value + 20 mV)

Rise Time

< 15 ns into a 50 ohm load (10% to 90% full scale step)

Aberrations

< 5% of p-p amplitude, +/- 50 mV

Flatness

+/- .5 dB to 10 MHz, +/- 1 dB to 30 MHz

Filters

35 MHz, 6-pole elliptical LPF; DDS mode

35 MHz, 3-pole Bessel LPF; AWG mode

Sync Output

Connector

Front Panel BNC.

Output is synchronous with output waveform
In DDS mode, the sync output is logic high during the positive part of the cycle and logic low during the negative part of the cycle as measured from the displacement/offset.

Output Impedance

50 Ω, ± 1%

Level

TTL Compatible

Marker Output

Positive pulse, user programmable and synchronous with the waveform output.

Output

Front Panel PS2 connector

One Of 8 PXI Trigger Lines

PS2 Output Impedance

50 Ω, ± 1%

PS2 Output Level

TTL Compatible

Trigger Modes

Continuous

Output Is Continuously Generated

Triggered

Output waveform is triggered by an external or software triggered event. The external trigger signal edge may be a rising or falling edge.

Start/Stop

Output waveform is triggered by a trigger signal edge. Waveform is continuously generated until the occurrence of a trigger edge. The trigger signal may be external or software generated. The external trigger signal edge may be their rising and or falling edge.

Gated

Same as triggered mode except that the waveform is generated for as long as the gate signal stays high when the gate signal goes low the output goes quiescent.

Gated Hold

Same as gated mode except that when the gate signal goes high the waveform freezes until the gate signal goes low.

Burst

Output waveform will become active on the occurrence of a trigger edge. The selected waveform is generated for a preset number of cycles between 1 and 1,048,576. Output will then disable.

Trigger Sources

Software Trigger

Generate A Trigger Via A Function Call

Internal Trigger Generator

Programmable Trigger Generator

Frequency Range: 0.01 Hz 50 Mhz

External Trigger

External Trigger Input Via The External Trigger / Gate Input. Active Trigger Edge Is Programmable.

PXI Star Trigger

Select PXI Star Trigger As A Trigger Source

PXI Trigger

Select One Of 8 PXI Triggers For Trigger Functionality.

Note: The PXI Trigger Can Be Used With Other Trigger Source Selections.

External Trigger / Gate Input

Connector

Front Panel BNC

Impedance

10k ohm Nominal

Threshold Level

TTL

Repetition Rate

DC To 10 MHz

Min Pulse Width

50 ns

Slope

Positive Or Negative Going Edge

Reference Clock

Internal Reference

40 Mhz Oscillator

Accuracy: 50 ppm

External Reference Input

PXI 10 Mhz

External Clock Reference Input (10 MHz)

External Clock Reference Input

Front Panel PS2 Connector

Input impedance: 10k Ohm Nominal

Threshold level: TTL

Reference Clock Output

Connector

Front Panel PS2

Frequency

10 MHz

Output Level

TTL

Output Impedance

50 Ohms

Waveform Modulation

Modulation

AM or FM

Modulation Source

Internal or External

Internal Modulation Waveform

Sine, square, triangle, ramp, noise,

Frequency range: 0.01 Hz to 20 KHz

Modulation Range

0 to 100%

External Modulation Input

Front panel PS2

Input voltage range: 5 volts p-p for 100% modulation

Input impedance: 10 K ohms nominal

Bandwidth: DC to 20 KHz

General

Power Requirements

15 W (Max.)

Current Consumption (Max)

+5 V @ 1 A

+12 V @ 300 mA

-12 V @ 300 mA

+3.3 V @ 1 A

Weight

Approx. 12 oz.

Size

3U, single slot

Temperature

Operating

Storage

0° C to 50° C

-20° C to 70° C

Humidity

(Non-Condensing)

5% to 95%, < 70° C

Safety

Designed to meet IEC 1010-1, UL 3111-1, and

CSA 22.2#1010

Note: Specifications are subject to change without notice