Products » Digital I/O

Discussion groups on Digital Input/Output products supported by the GTDIO/DIOEasy software including GX50xx, GX51xx, GX52xx, etc. Additional support information is also available in our Knowledge Base.

Showing 1 - 10 of 22 Items | 1 2 3 | View All
Gowan W.

Oct 13, 2021
0 Replies
22 Views

GX5641 Differential DIO PIN OUTS

Documentation points to NI 781xR but that shows DIO only upto DIO39 and was expecting upto DIO128

or is it just DIO32 on each of the 4 connectors????
Read more...
10/13/2021 6:05:08 AM by Gowan W.

Ozan O.

Dec 21, 2020
0 Replies
175 Views

GX5292e Configuration I/O and Reading/Writing Data

Hi,

I am using GX5292e LVDS card. I am trying to configurate the pins output or input. Also, When I try to write data which is such a "01010101" etc, I am not able to...
Read more...
12/21/2020 1:02:19 AM by Ozan O.

Jeffrey B.

Oct 26, 2020
0 Replies
146 Views

GTDIO Firmware / Driver versions

I saw that back in 2012 there was a question about firmware. We recently faced an issue where I thought that our drivers may have been causing what we saw. It ended up be...
Read more...
10/26/2020 7:09:36 AM by Jeffrey B.

Solution Available
Michal M.

Apr 7, 2020
1 Reply
162 Views

Pause and Resume / GX5280

Hello Everyone,

We consider to use one of the GX52## family products for CMOS detector addressing (in non-sequential way). I'm wondering if it is possible to pause exe...
Read more...
4/7/2020 10:44:38 AM by Dale J.

Sanjay E.

Feb 21, 2018
4 Replies
1830 Views

Pattern Creation with 16 channels using DIOEasy Tool

Hi everyone,

We want to utilize the GX5295's DIO memory effectively, so planning to use 16 channel mode instead of 32 channel mode.
We are creating the sample DIO fil...
Read more...
4/2/2018 11:58:34 AM by Sanjay E.

Solution Available
Sanjay E.

Jan 16, 2018
1 Reply
1399 Views

GX5295 Dio Channel Selection

Hi All,

I've a pattern with 32 channels enabled, but in this case GX5295 DIO maximum can support maximum 64M as vector depth for each channel.
(Note: I have to increa...
Read more...
1/16/2018 9:32:40 AM by Jason D.

Solution Available
Sanjay E.

Jan 2, 2018
8 Replies
1769 Views

Multiple Patterns Loading into GX5295 DIO's Memory

Hi all,

I'm using GX5295 DIO card in PCI Chassis linked to a PC.

I wanna to call the DIO_LoadFile of the GtDio32.dll to load Multiple pattern files to the board's ...
Read more...
1/16/2018 9:31:38 AM by Jason D.

Benoit V.

Dec 3, 2014
0 Replies
3504 Views

Using Gx3500 IRQ

Hi,
I would like to implement IRQ in my GX3500 project.
In the User Guide page 35 there is an IRQ Pin Alias describe but nowhere else i ve found the pin assignment for ...
Read more...
12/3/2014 6:28:52 AM by Benoit V.

Miha L.

Jul 21, 2014
0 Replies
3013 Views

DIOEasy - start the application programmatically from C#

We are looking into launching the DIOEasy editor from our C# code.
Using the System.Diagnostic.Process to start DIOEasy works fine, but when we add a filename as argumen...
Read more...
7/21/2014 1:00:41 PM by Miha L.

Solution Available
Garrett O.

May 28, 2014
1 Reply
2870 Views

Writing Commands to a Scope

I'm currently trying to read in information from a scope about an LED, namely the peak to peak value. Occasionally, I will encounter the attached error when sending t...
Read more...
5/28/2014 2:51:47 PM by Victor B.

Showing 1 - 10 of 22 Items | 1 2 3 | View All

Please Note
You need to have a M@GIC account to participate in the Forums.
Not yet registered on our website? Click here to register today!

All content, information and opinions presented on the Marvin Test Solutions User Forums are those of the authors of the posts and messages and not Marvin Test Solutions'. All attachments and files are downloaded at your own risk. [Read More]